Diamond Audio MP654 6.5" PRO Full-Range Co-Ax Horn Speaker + MICRO4V2 4-Channel Full Range Class D Amplifier + MSMP694LK 14+Harley Davidson Cut in Lid Kit with MP694 + M1SRT

General Features:

• 150W RMS/300 MAX Power Handling
• Ferrite Strontium High Temp Magnet structure
• Heavy Duty Die-cast Aluminum Basket
• 1.5” 4 Ohm – Single Layer High Temp Voice Coil with Black Coated Voice Coil former for Woofer
• 1.0” 8 Ohm – Single Layer High Temp Voice Coil for Tweeter
• Advanced Voice Coil Heat Sink Design for Better Heat Dissipation
• Frequency Response: 110Hz -18Khz
• High Sensitivity 101dB 1W/1M
• 12dB Crossover
• Mounting Depth: 3.33” / 84.6mm
• Mounting Diameter: 5.73” / 145.5mm

Specifications

• SPL (dB-MidBass) 92.7
• SPL (dB-Tweeter) 107
• Re(Ω)[series] 3.2
• Qms 10.73
• Qes 0.47
• Qts 0.45
• Fs(Hz) 103.3
• Vas(L) 6.6
• Cms(mm/N) 0.24
• Mms(g) 9.7
• Sd(m2) 138.9
• BL(T*M) 6.5
• Xmax(mm) 1.0
• Pwr(W) NOM/MAX 150/**300
• Total Diameter 6.52 (165.5) in. (mm)
• Mounting Diameter 5.73 (145.5) in. (mm)
• Mounting Depth 3.33 (91.6) in. (mm)
• Total Depth 3.88 (98.6)in. (mm)
• Magnet Diameter 3.94 (100) in. (mm)

MSMP694LK 14+ Harley Davidson Cut in Lid Kit with MP694 6 X 9” PRO Full-Range Co-Ax Horn Speaker

General Features:

• 150W RMS/300W MAX Power Handling
• Ferrite Strontium High Temp Magnet structure
• Heavy Duty Die-cast Aluminum Basket
• 1.5” 4 Ohm - Single Layer High Temp Voice Coil with Black Coated Voice Coil former for Woofer
• 1.0” 8 Ohm - Single Layer High Temp Voice Coil for Tweeter
• Advanced Voice Coil Heat Sink Design for Better Heat Dissipation
• Frequency Response: 80Hz -18Khz
• High Sensitivity 101dB 1W/1M
• 12dB Crossover
• Mounting Depth: 3.99” / 101.3mm
• Mounting Diameter: 8.86” x 5.98” / 225 x 152mm
• Nominal Impedance (ohms) N/A
• Fs-Free Air Resonance (Hz) 6
• Vas (Liter) 2
• Qts 42
• Qes 43
• Qms 42
• Re (Ω)[series] 2
• Sd (cm²) 7
• Cms (mm/N) 25
• Mms (g) 1
• BL (T*M) 6
• SPL (db) (95.6) (107)
• Total Diameter 33X6.57 (237X167) in. (mm)
• SPL (dB-Tweeter) 107
• SPL (dB-MidBass) 6
• Total Depth 26 (108.3) in. (mm)
• Xmax - Inch(mm) 0
• Mounting Diameter (inch/mm) 86X5.98 (225X152) in. (mm)
• Mounting Depth 99 (101.3) in. (mm)
• Magnet Diameter (E) 94 (100) in. (mm)

MICRO4V2 MICRO 4-Channel Full Range Class D Amplifier

General Features:

• Full Range Class D IR Chipset
• DirectFET Power Mosfet Output Stage
• SMD Technology on 4 layer Glass PC Board
• ICAD circuit provides superior overload protection
• Frequency response 20 Hz – 30kHz
• Variable 12db crossovers
• Bridgeable / 2ch-4ch switch control
• BTR (BlueTooth Receiver enabled)
• MICRO Bass boost +12DB @45Hz
• Premium 8 and 4 gauge power connections
• Multi channels / Mono channel

Specifications

• RMS Power (2 Ω) 150 W X 4
• RMS Power (4 Ω) 80 W X 4
• Bridged (mono 4 Ω) 300 W X 2
• Topology Full Range Class D
• Power Supply Full PWM
• Power Supply Threshold 10.0DVC – 17.0DVC
• Idle Current (0.7A)
• THD 4 (1KHz @4Ω) 0.5%
• S-N Ratio (A-weighted @ 1W) -85dBA
• S-N Ratio (A-weighted @ 1W) -101.1dBA
• Input Sensitivity – Low Input Level 200mV – 10.0V
• Input Sensitivity – High Input Level N/A
• Input Impedance – Low Input Level 20 KΩ
• Impedance – High Input Level 20 KΩ
• Output Impedance 0.018Ω
• Damping Factor (50Hz @ 4Ω) >70
• Bandwidth (-3dB) 10Hz-35Hz
• Crossover (-12 dB/ Oct) – Variable High Pass 40Hz-400Hz
• Crossover (-12 dB/ Oct) – Variable Low Pass 40Hz-400Hz
• Crossover (-12 dB/ Oct) – Variable Subsonic N/A
• Fuse Rating (ATC) 40A
• Dimensions- Length x Width x Height (inches) 9.07″ x 4.0″ x 1.46″
• Dimensions- Length x Width x Height (mm) 230.5 x 103 x 37.2 mm 

M1SRT Compression Extreme Output Tweeter Short Horn version

• 50W/*100W MAX RMS Power Handling
• 107dB Sensitivity
• Composite Rubber Mounting Frame
• 12dB  Crossover included for maximum protection
• Radial Slit Phase Plug for Better Response
• Over-All Diameter: 2.28” / 57.9mm
• Overall Depth: 2.22” / 56.4mm