Viper 474V 4-Button Remote

Viper 1-Way 4-Button Remote Control Replacement Transmitter 

This remote control is from the original manufacturer ensuring that you are receiving a genuine NEW product made for your Viper system.

This will replace many of the Viper discontinued remote controls along with Automate, Avital, Hornet, Rattler, Python, Sidewinder and Valet systems.

Replaces or can be used in conjunction with the following remote controls:

• 474V
• 474A
• 474C
• 474L
• 474P
• 474T
• 7141V
• 7142V
• 7145V
• 7146V

Direct replacement for the following VIPER systems:

• 100HF
• 300HF (ESP)
• 300+HF
• 500HF (ESP)
• 550HF (ESP)
• 600HF (ESP)
• 800SHF (ESP)
• 130HV
• 210HV
• 350HV
• 150 (ESP)
• 160XV
• 330V
• 560XV
• 571XV
• 650XV
• 671XV
• 771XV
• 850XV
• 211
• 1000
• 1002
• 3000
• 3002
• 5000
• 5002
• 7900

Direct replacement for the following VALET systems:

* Date code can be found on the back of the main alarm or remote start brain. It will be on a white sticker with "OK" marked on it.

Direct replacement for the following Automate systems:

Direct replacement for the following Hornet systems:

Direct replacement for the following Python systems:

Direct replacement for the following Sidewinder systems:

Please make sure you have a working control unit installed in the vehicle prior to ordering this remote control. Programming instructions are included in the package and will require accessing your valet/programming switch. Video instructions will be available on our YouTube page under remote controls.

PROGRAMMING INSTRUCTIONS: 

Use the following learn routine to add transmitters to your system or to change button assignments if desired.

The learn routine may be locked if previously programmed using the Bitwriter. If the horn generates one long honk when attempting to program the unit, the learn routine is locked and must be unlocked using the Bitwriter™ before proceeding. Find a local Viper dealer.

The Valet/Program switch, plugged into the blue port, is used for programming. There is a basic sequence of steps to remember whenever programming this unit: Key, Choose, Transmit and Release.

1. Key. Turn the ignition to the ON position.

2. Choose. Within 10 seconds, press and release the Program switch the number of times corresponding to the desired channel listed below. Once you have selected the channel, press the switch once more and HOLD it. The LED will flash and the horn will honk (if connected) to confirm the selected channel. Do not release the Program switch.

1 Auto Learn*

2 Arm Panic On/Panic Off

3 Disarm Panic Off

4 Silent Mode Channel 2 RED/WHITE

5 Remote Start

6 Channel 4 VIOLET/BLACK

7 Short Run/Turbo

8 Timer Mode

9 Arm/Disarm/Panic

10 Panic Only

11 Defogger Control

12 Delete All Transmitters**

*NOTE: For Auto Learn Configurations, see Transmitter Configurations section of this guide.

**NOTE: If any button from a known transmitter is programmed to Channel 12, all transmitters will be erased from memory and will revert to the default feature settings. This is useful in cases where the customer's transmitters are lost or stolen.

3. Transmit. While HOLDING the Valet/Program switch, press the button on the transmitter that you would like to control the selected receiver channel. The unit will chirp to confirm that the code has been successfully programmed. It is not possible to teach a transmitter button to the system more than once.

4. Release. Once the code is learned, the Valet/Program switch can be released.

Learn Routine will be exited if:

■ Ignition is turned off.

■ Program switch is pressed too many times.

■ More than 15 seconds elapses between programming steps. One long horn honk indicates that Learn Routine has been exited.

Please contact us if you have any questions.